Real Server Changes

Content Server Changes

This section is split in to the following sections:

Transparency

Transparency is suitable for Service Type Layer 4 load balancing
only, Caching and Compression are not available when transparency is
enabled. Transparency is used when you need the source address of the
client making the request:

How it works

  • Client sends a request to the edgeNEXUS
  • Request is received by edgeNEXUS
  • MAC address is changed. Request forwarded to content servers
  • Response sent to edgeNEXUS
  • edgeNEXUS routes the response to the client

Transparency Diagram

Required Content Server Configuration

General

  • Content servers need to be configured to use the edgeNEXUS Eth0 IP
    address as their default gateway for single arm configuration
  • Content server need to be configured to use the edgeNEXUS Eth1 IP
    address as their default gateway for dual arm configuration
  • The content server and the load balancer must be in the same
    subnet

Windows

  • The content server needs to have a loopback or Alias configure
    with the IP address of the Channel or VIP
    • Network metric must be 254 to prevent response to ARP requests
    • Modify the netmask to be 255.255.255.255
    • Add a loopback adapter in Windows Server 2012 – Click here
    • Add a loopback adapter in Windows Server 2003/2008 – Click here
  • Run the following in a command prompt
    • netsh interface ipv4 set interface “net” weakhostreceive=enabled
    • netsh interface ipv4 set interface “loopback”
      weakhostreceive=enabled
    • netsh interface ipv4 set interface “loopback”
      weakhostsend=enabled
  • To Disable – should you wish to back out of the configuration
    • netsh interface ipv4 set interface “net”
      weakhostreceive=disabled
    • netsh interface ipv4 set interface “loopback”
      weakhostreceive=disabled
    • netsh interface ipv4 set interface “loopback”
      weakhostsend=disabled

The network metric is set in  the Advanced TCP/IP Settings of the
loopback Interface

Linux

1.    Add a permanent
loopback interface
2.    Edit “/etc/sysconfig/network-scripts”
ifcfg-lo:1
DEVICE=lo:1
IPADDR=x.x.x.x
NETMASK=255.255.255.255
BROADCAST=x.x.x.x
ONBOOT=yes
3.    Edit
“/etc/sysctl.conf”
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.eth0.arp_ignore = 1
net.ipv4.conf.eht1.arp_ignore = 1
net.ipv4.conf.all.arp_announce = 2
net.ipv4.conf.eth0.arp_announce = 2
net.ipv4.conf.eth1.arp_announce = 2
4.    Run “sysctl – p”

 

Direct Server Return

Direct Server Return, or
DSR as it’s widely known (DR – Direct Routing in some circles) allows
the server behind the load balancer to respond directly to the client
bypassing the edgeNEXUS on the response. DSR is suitable for using with
Layer 4 load balancing only therefore Caching and Compression are not
available when enabled.
Layer 7 load balancing with this method will
not work therefore there is no persistence support other than source
IP.   SSL/TLS load balancing with this method is not ideal as
there is only source IP persistence support. 

How it Works

  • Client sends a request to the edgeNEXUS
  • Request received by edgeNEXUS
  • Request routed to content servers
  • Response sent directly to client without passing through JetNEXUS

DSR Diagram

Required Content Server Configuration

General

  • The content server default gateway should be configured as
    normal. (Not via the jetNEXUS)
  • The content server and the load balancer must be in the same
    subnet

Windows

  • The content server needs to have a loopback or Alias configure
    with the IP address of the Channel or VIP
    • Network metric must be 254 to prevent response to ARP requests
    • Add a loopback adapter in Windows Server 2012 – Click here
    • Add a loopback adapter in Windows Server 2003/2008 – Click here
  • Run the following in a command prompt
    • netsh interface ipv4 set interface “net” weakhostreceive=enable
    • netsh interface ipv4 set interface “loopback”
      weakhostreceive=enable
    • netsh interface ipv4 set interface “loopback”
      weakhostsend=enable

Linux

1.    Add a permanent
loopback interface
2.    Edit “/etc/sysconfig/network-scripts”
ifcfg-lo:1
DEVICE=lo:1
IPADDR=x.x.x.x
NETMASK=255.255.255.255
BROADCAST=x.x.x.x
ONBOOT=yes
3.    Edit
“/etc/sysctl.conf”
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.eth0.arp_ignore = 1
net.ipv4.conf.eht1.arp_ignore = 1
net.ipv4.conf.all.arp_announce = 2
net.ipv4.conf.eth0.arp_announce = 2
net.ipv4.conf.eth1.arp_announce = 2
4.    Run “sysctl – p”

Gateway

Gateway
mode allows you to route all traffic through the jetNEXUS, this allows
traffic originating from the content servers to be routed via the
edgeNEXUS to other networks via the interfaces on the edgeNEXUS unit.
Using the device as a gateway device for content servers should be used
when running in multi interface mode

How it works

  • Client sends a request to the edgeNEXUS
  • Request is received by edgeNEXUS
  • Request sent to content servers
  • Response sent to edgeNEXUS
  • edgeNEXUS routes the response to the client

Required Content Server Configuration

  • Content servers need to be configured to use the edgeNEXUS Eth0 IP
    address as their default gateway
  • Content servers need to be configured to use the edgeNEXUS Eth1 IP
    address as their default gateway for dual arm configuration
  • The content server and the load balancer must be in the same
    subnet

Windows

On
windows the following commands must be run at the command prompt
running in administrator mode. Where net is the name of the name of the
interface:

  • The content server needs to have a loopback or Alias configure
    with the IP address of the Channel or VIP
    • Network metric must be 254 to prevent response to ARP requests
    • Modify the netmask to be 255.255.255.255
    • Add a loopback adapter in Windows Server 2012 – Click here
    • Add a loopback adapter in Windows Server 2003/2008 – Click here
  • Run the following in a command prompt
    • netsh interface ipv4 set interface “net” weakhostreceive=enable
    • netsh interface ipv4 set interface “loopback”
      weakhostreceive=enable
    • netsh interface ipv4 set interface “loopback”
      weakhostsend=enable 

Linux

1.    Add a permanent
loopback interface
2.    Edit “/etc/sysconfig/network-scripts”
ifcfg-lo:1
DEVICE=lo:1
IPADDR=x.x.x.x
NETMASK=255.255.255.255
BROADCAST=x.x.x.x
ONBOOT=yes
3.    Edit
“/etc/sysctl.conf”
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.eth0.arp_ignore = 1
net.ipv4.conf.eht1.arp_ignore = 1
net.ipv4.conf.all.arp_announce = 2
net.ipv4.conf.eth0.arp_announce = 2
net.ipv4.conf.eth1.arp_announce = 2
4.    Run “sysctl – p”

CONTACT US

We're not around right now. But you can send us an email and we'll get back to you, asap.

Sending

Log in with your credentials

or    

Forgot your details?